If you’ve ever worked with high-voltage (HV) circuits—think power supplies, industrial controls, automotive electronics, or grid-stabilization systems—chances are you’ve crossed paths with X7R series disc capacitors. As a supplier of these parts, I get tons of questions weekly, and one that pops up more than most is: “What’s the actual capacitance range for X7R HV disc capacitors?” It’s a fair ask—capacitance is make-or-break for how these components perform under stress. Let’s break it down straight, no stuffy datasheet jargon, and tie in what matters most for you as a designer or buyer. X7R Series HV Disc Capacitor

First, let’s get the basics out of the way to ground this. X7R is a Class II ceramic capacitor dielectric, right? Its superpower is a tight capacitance tolerance across temperature—rated to stay within ±15% from -55°C to 125°C, which is way more consistent than cheaper Class I dielectrics like NPO. For HV versions, that’s capacitors rated for 500V up to, well, way higher (we stock up to 30kV X7R disc caps, fyi), so the capacitance range shifts a bit as voltage goes up. That’s the big mistake I see engineers make: assuming the same cap range applies to 500V and 10kV parts. It doesn’t.
Let’s start with the most common X7R HV disc cap tier: 500V and 1kV rated units. These are the workhorses for low-to-mid-voltage industrial gear, EV battery management systems (BMS) aux circuits, and consumer high-power chargers. For these, the capacitance range is pretty broad—most brands, including our stock, go from 100pF up to 10µF. Wait, 10µF might sound low for some, but remember: higher capacitance in ceramic disc caps needs thicker dielectric to handle HV, and that thickening can eat into how much space you can fit. For 500V/1kV X7R, you’ll almost never see a cap bigger than 10µF in disc form factor—you’d need a different package like a multilayer ceramic (MLCC) or a film cap for higher farad values, and those aren’t X7R disc.
Now bump up the voltage to 2kV, 5kV, and 10kV—these are for the heavy hitters: medium-voltage inverters, power distribution equipment, medical X-ray gear, and automotive HV connectors. Here, the dielectric has to get way thicker to withstand that kind of voltage, so the max capacitance drops hard. For 2kV X7R discs, the top end is around 4.7µF; 5kV tops out at 1µF, and 10kV? We rarely go above 470nF. Wait, hold up—470nF at 10kV is a big cap, and I’ve had designers ask why we don’t have a 1µF 10kV X7R disc. The short answer is physics: X7R dielectric has a breakdown field of ~200V per micron, so a 10kV cap needs at least 50 microns of dielectric. To get 1µF in a disc, you need a electrode area of around 500mm²—so a disc that’s like 20mm in diameter. That’s a massive part, and it’s not practical for most applications, plus it’d cost 10x what a 470nF 10kV cap does. So even if you could make it, it’s not useful for 99% of projects.
And then there’s the highest tier we stock: 20kV and 30kV X7R HV discs. These are for specialized stuff—high-voltage test equipment, pulse circuits, aerospace components. Here, the capacitance range narrows even more: we only carry from 10pF up to 100nF. A 100nF 30kV disc is tiny, like 12mm across, because we can push the dielectric a bit thinner than the minimum breakdown (we test every lot to make sure, no cutting corners) to keep size manageable. If you need higher capacitance than that at 20kV+, you’re looking at a different dielectric or package—no X7R disc can do it, trust me.
Wait, let’s address a common misconception here. Some cheap overseas sellers will list a “X7R HV disc cap” with 1µF at 10kV, but that’s almost always a bait and switch. They’re either using a lower-quality dielectric that’ll drift out of tolerance 20% after a month, or it’s a real X7R cap but rated at 500V, not 10kV, so it’ll arc and fail in weeks. We test every single lot of our X7R HV discs at full rated voltage at 125°C—no exceptions—so you don’t get that garbage. That’s why when I tell designers “10kV X7R is max 470nF,” it’s based on real, tested parts, not marketing fluff.
Another thing to note: tolerance can shift slightly at the high and low ends of that range. For example, a 10pF 30kV X7R cap will have a tolerance of ±5% normally, while a 100nF will be ±10%—that’s just how the electrode etching works at tiny sizes. And if you’re working at extreme temps (above 125°C or below -55°C), you might want to derate the capacitance a bit, but that’s a separate chat for another time.
Now, why does this range matter for your project? Let’s say you’re designing a DC-DC converter that needs a 2µF 2kV cap for ripple suppression. If you reach for a 1µF 5kV cap, that’s too low, and a 4.7µF 2kV cap will work, but it’ll be bulkier than you need. If you mistakenly order a 1µF 10kV cap, it’ll either be overkill on voltage (wasting money) or a fake part that fails. As a supplier, we get a ton of repeat customers because we don’t just say “here’s the range”—we help match your voltage, capacitance, and form factor to avoid those mistakes.
Wait, I should also mention: some people mix up “X7R HV disc” with “high-capacitance HV ceramic caps.” The latter is usually MLCCs, which can get up to 100µF, but they’re not disc-shaped, and they don’t have the same long-term reliability as disc caps for harsh environments (discs are way less prone to mechanical stress from vibration, which is a big deal in automotive or industrial gear). So if you specifically need a disc shape, stick to the ranges we talked about: 100pF–10µF for <1kV, 100pF–4.7µF for 2kV, 10pF–1µF for 5kV, 10pF–470nF for 10kV, and 10pF–100nF for 20kV+. That’s the sweet spot for reliable, tested X7R HV disc caps.
I’ve had a designer reach out to me last month saying they needed a 2.2µF 5kV cap for a welding machine control board. He’d tried a cheap Amazon part and it arced after 2 weeks, burning out his whole prototype. We sent him our 2.2µF 5kV X7R discs, and his production run went off without a hitch. That’s the kind of value we bring—knowing the range, and making sure you get the right part for the job, not just a part that fits the spec on paper.

If you’re still not sure where your project falls, or you’re hunting for a specific value that doesn’t seem to fit, just reach out. We don’t do hard sell—we’ll tell you if a part is a bad fit, help you adjust your design if needed, or point you to a different part type if X7R disc isn’t the right choice. No hidden fees, no sketchy lot numbers, just parts that we’d use in our own gear.
100mA Standard Recovery HV Diode So to wrap this up, the capacitance range for X7R HV disc capacitors isn’t a one-size-fits-all number—it shifts with rated voltage, form factor practicality, and dielectric physics. For most common applications under 1kV, you’re looking at 100pF to 10µF, while higher voltage parts taper off to as low as 10pF for 30kV. If you need reliable, tested X7R HV disc caps that fit these ranges (or have a custom request), don’t hesitate to connect with our team to discuss your needs.
References
- Murata Manufacturing Co., Ltd. "Multilayer Ceramic Capacitors for High-Voltage Applications." Datasheet, 2023.
- AVX Corporation. "X7R Dielectric Characteristics and Capacitance Stability." Application Note, 2022.
- International Electrotechnical Commission (IEC). "Ceramic Capacitors for High-Voltage Power Systems." Standard 60384-21, 2021.
- TDK Corporation. "Disc Capacitor Design for High-Voltage and Harsh Environment Operation." Technical Bulletin, 2023.
Anshan HVRTION Electronic Technology Co., Ltd.
As one of the most professional x7r series hv disc capacitor manufacturers and suppliers in China, we’re featured by quality products and good price. Please rest assured to buy discount x7r series hv disc capacitor for sale here and get quotation from our factory. We also accept customized orders.
Address: 17 East Jiefang RD., Tiedong District, Anshan, Liaoning, China.
E-mail: hvrtion@hotmail.com
WebSite: https://www.hvrtion.com/